SAJ

Beta support overview

In beta and available on request. The additions in this overview require the matching integration or controller update and are not confirmed as part of the standard customer release. Request them through your existing Eniris support conversation. The status applies to these additions, not to every existing function of the devices listed elsewhere on this page.

H1 hybrids

H2 hybrids

R5 PV inverters

eManager systems

See integration details for connection requirements and operating limitations.

Supported Devices

The R5 and R6 are PV-only (on-grid) inverters without a battery. The EMS reads their production and can limit their output. They use the same SAJ Modbus TCP connection as the hybrid models, so the inverter needs a connection to the local network.

For a site connected through a SAJ eManager-C1 Pro, use the separate eManager connection below instead of selecting an individual inverter model.

SAJ eManager-C1 Pro

The eManager is a local gateway for the inverters connected to it. This connection reads the combined installation through the eManager rather than opening a separate connection to every inverter.

Connect the eManager

1. Connect the eManager and the EMS to the same local network. Follow the Ethernet wiring guidelines.
2. Open the controller's device setup and select SAJ, then eManager.
3. Enter the eManager's IP address, TCP port 502 and configured Modbus address. This connection uses Ethernet, not the RS485 settings for other SAJ equipment.
4. Fill in How many inverters are connected to the eManager? with the actual number connected to this gateway.
5. Add the connection and check the displayed system power, battery state of charge, grid measurements, phase voltages and frequency before enabling energy management.

Why the inverter count matters

The eManager combines readings from its connected inverters. The controller uses the inverter count to convert the combined voltage and frequency readings back to meaningful values. For example, four connected inverters can return a combined frequency reading of 200 Hz; an inverter count of 4 produces the expected 50 Hz display.

If voltage or frequency appears to be a multiple of the expected value, correct Inverter count. Do not compensate by changing the electrical installation settings. The power readings represent the combined system and are not divided by this count.

The connection provides an AC active-power setpoint for the combined system. It does not provide independent setpoints for every inverter behind the eManager, or a separate PV power-limit command.

Configuration

1: Physical Connection Setup

For Ethernet Connection:

1. Locate the communication interface on your SAJ inverter
2. Connect an ethernet cable between the inverter and your local network
3. Follow the ethernet wiring guidelines for proper installation

For RS485 Connection:

1. Locate the RS485 port on your SAJ inverter
2. Connect the RS485 cable according to the following pinout:
   • PIN A: RS485+
   • PIN B: RS485-
   • GND: Ground (if available)

2: Network Configuration

1. By default, the inverter is set to obtain an IP address automatically via DHCP
2. If using a static IP configuration:
   • Access the inverter's web interface
   • Navigate to Network Settings
   • Configure the IP address, subnet mask, and gateway as needed

3: Communication Settings

For optimal performance, ensure the following communication parameters:

• Modbus TCP port: 502 (default)
• RS485 baud rate: 9600
• Data bits: 8
• Stop bits: 1
• Parity: None

Wiring

Ethernet Connection

• Use CAT5e or CAT6 ethernet cable
• Maximum cable length: 100 meters
• Follow the guidelines for ethernet wiring

RS485 Connection

• Use shielded twisted pair cable
• Maximum cable length: 1000 meters
• Connect the shield to ground at one end only
• Maintain proper RS485 bus topology

eSAJ Home settings

Troubleshooting

Common issues and solutions:

1. No Communication

   • Check physical connections
   • Verify network settings
   • Ensure proper Modbus address configuration

2. Intermittent Connection

   • Check cable quality and connections
   • Verify there's no electromagnetic interference
   • Ensure proper cable routing

Beta integration details

SAJ improvements

H1 settings reads are retried when the inverter intermittently refuses them, and inverter AC power uses the corrected register/sign. H2 control has a separate improvement that accounts for backup-port loads when calculating the grid-export allowance.

H1 and R5 custom variants

H1 custom control corrects battery-current scaling to 0.05 A per step on the verified firmware and the relevant power signs. This scale must not be assumed for every SAJ firmware. A separate R5 single-phase variant provides monitoring for one, two or three MPPT inputs; that variant is read-only.

eManager C1 Pro

A custom implementation provides separate battery, PV and reactive-power requests for an eManager C1 Pro configuration. It is prepared but has not completed physical commissioning. Measurement aggregation depends on the number of connected inverters, and signed reactive-power readback still depends on manufacturer firmware. Do not reuse the investigated six-inverter scaling on another topology.